Post a Comment. If a fuse has blown, the element inside the fuse will melt. Before replacing a blown fuse, disconnect the negative battery cable. If the replacement fuse blows, this indicates an electrical problem.

2015 kia sportage headlight fuse location full

Avoid using the system involved and immediately consult an authorized Kia dealer. It may cause extensive wiring damage and a possible fire.

KIA Sportage (SL; 2011-2016) fuses and relays

Do not use a screwdriver or any other metal object to remove fuses because it may cause a short circuit and damage the system. The fuses, relays and terminals may be fastened incompletely, and it may cause a possible fire.

It may cause contact failure and system malfunction. Inner panel fuse replacement. Pull the suspected fuse straight out. Use the removal tool provided on the engine compartment fuse panel cover. Check the removed fuse; replace it if it is blown.

2015 kia sportage headlight fuse location full

Spare fuses are provided in the engine compartment fuse panel. Push in a new fuse of the same rating, and make sure it fits tightly in the clips. If you do not have a spare, use a fuse of the same rating from a circuit you may not need for operating the vehicle, such as the power outlet fuse.

If the headlights or other electrical components do not work and the fuses are OK, check the fuse panel in the engine compartment. If a fuse is blown, it must be replaced. Your vehicle is equipped with a memory fuse to prevent battery discharge if your vehicle is parked without being operated for prolonged periods. Use the following procedures before parking the vehicle for prolonged periods. Remove the fuse panel cover by pressing the tab and pulling the cover up.

To remove or insert the fuse, use the fuse puller in the engine compartment fuse panel. If the main fuse and multi fuse is blown, it must be removed as follows:. Email This BlogThis! No comments:. Newer Post Older Post Home. Subscribe to: Post Comments Atom.The system automatically turns off the exterior lights when the driver removes the ignition key and opens the driver-side door.

If necessary, to keep the lights on when the ignition key is removed, perform the following: 1 Open the driver-side door.

Headlight escort function if equipped The headlights and taillights remain on for approximately 20 minutes after the ignition key is removed or turned to the ACC or LOCK position. The headlights and taillights can be turned off by pressing the lock button on the transmitter or turning off the light switch from the headlight or Auto light position. Lighting control The light switch has a Headlight and a Parking light position. To operate the lights, turn the knob at the end of the control lever to one of the following positions: 1 OFF position 2 Parking light position 3 Headlight position 4 Auto light position if equipped.

Parking light position When the light switch is in the parking light position 1st positionthe tail, license and instrument panel lights will turn ON. Headlight position When the light switch is in the headlight position 2nd positionthe head, tail, license and instrument panel lights will turn ON.

Auto light position if equipped When the light switch is in the AUTO light position, the taillights and headlights will turn ON or OFF automatically depending on the amount of light outside the vehicle. This will ensure better auto-light system control. The cleaner may leave a light film which could interfere with sensor operation. High beam operation To turn on the high beam headlights, push the lever away from you.

Pull it back for low beams. The high beam indicator will light when the headlight high beams are switched on. To prevent the battery from being discharged, do not leave the lights on for a prolonged time while the engine is not running.

To flash the headlights, pull the lever towards you. It will return to the normal low beam position when released. The headlight switch does not need to be on to use this flashing feature. Turn signals and lane change signals The ignition switch must be on for the turn signals to function. To turn on the turn signals, move the lever up or down A. The green arrow indicators on the instrument panel indicate which turn signal is operating.

They will self-cancel after a turn is completed.

2011-2016 Kia Sportage Interior Fuse Check

If the indicator continues to flash after a turn, manually return the lever to the OFF position. To signal a lane change, move the turn signal lever slightly and hold it in position B. The lever will return to the OFF position when released. If an indicator stays on and does not flash or if it flashes abnormally, one of the turn signal bulbs may be burned out and will require replacement.Kia Motor Sportage owners have reported 12 problems related to turn signal under the exterior lighting category.

The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Kia Motor Sportage based on all problems reported for the Sportage. Rear turn signals of the vehicle are below the lowest point of the lift gate, are mounted inside the bumper, and are recessed in the bumper. When turn signals are used, only the turn blinkers in the bumper blink while the traditional rear brake lamps are solid and do not indicate a turn.

The turn signals are too low for following vehicles to see and because they are recessed, the housing gets packed with snow, slush and dirt, making the activated signals indistinguishable. All kia Sportages have this poorly engineered feature, which may be as outside compliance as an early 70s malibu, and no turn signals in the brake light assembly. See all problems of the Kia Motor Sportage. Rear turn signals and reversed lights are not integrated with back brake lights. They are too low and placed under the bumper and on the side of the car.

The turn signals are not visible to cars behind. Have owned the vehicle for 6 weeks and have had a few very close incidents especially during the day in traffic. Cars do not slow down when I indicate and I have had two incidents where motorists have told me I had failed to signal and many instances of motorists honking.

Very dangerous when changing lanes and merging. Reverse lights cannot be seen. Very thin, not integrated with other back lights and placed too low down.

They look like reflectors and on a white car cannot be seen. I purchased two Sportages. My daughter drives one and has the same problems. I owned a sorento and forte which I traded in to get awd vehicles which I thought were safer for colorado driving.

Sportage is the only car with this issue. Kia won't integrate the turn signal with the brakes. Major safety issue. Newer model kia Sportage vehicles have low mounted turn signals that are seperate from the rest of the brake light assembly.This Kia Sportage was equipped with the newer style "Low Profile" mini blade fuses.

KIA Sorento (XM; 2010-2015) fuses and relays

If necessary, they may also be replaced with the slightly taller standard mini blade fuses. New low profile mini blade fuses in a variety of amperage ratings e. A white plastic fuse puller is included on the engine bay fuse block. If the tool is missing, you could use a pair of needle nose pliers with rubber insulated handles. Press in the release tab on the rear edge of the fuse box cover before pulling it straight off.

There is a fuse location diagram on the underside of the cover and also another one in your owner's manual. The white plastic fuse puller tool is located at the front left corner of the engine bay fuse block. Pull Out Access Cover Fuse Location Diagram Interior Fuse Block The interior passenger compartment fuse panel is located behind a rectangular plastic access cover on the lower area of the dashboard in front of where the driver's left knee would normally reside.

Insert your fingers in to the opening at the bottom of the panel and gently pull it out of the dashboard. There is a fuse location diagram on the back side of the cover and also another one in your owner's manual.

Fuse locations and circuit detail to find the right fuse

Pull the old fuse straight out of the socket and hold it up to a light source. If the thin metal strip inside the translucent plastic middle section appears to be broken or burnt, then the old fuse is most likely "blown" and should be replaced with a new one of the same amperage rating e.

If the thin metal bar in the center of the old fuse appears to be intact, it should still be good. But since new fuses are so cheap, it should still be replaced as part of your electrical issue troubleshooting process. Replace the white plastic fuse puller tool in to its holder near the front left corner of the panel. Re-insert the tabs on the top edge of the interior fuse block access cover in first before gently snapping in the retaining clips on the bottom edge.

Test the electrical component that you were having issues with such as the radio, wiper blades, tail lights, headlights, power windows, door locks, etc. If you are still having the same electrical problem, you might have a shorted wire somewhere or the component itself needs to be replaced. If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal.

Thank you! Note: I am not a registered charity. Donations are not tax deductible.Kia Motor Sportage owners have reported 19 problems related to headlights under the exterior lighting category. The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Kia Motor Sportage based on all problems reported for the Sportage. If you turn the car or take a bend in the road or drive down or up hill the distraction becomes a very bad problem as the shadow changes in size or moves.

Mostly on low beams but is also on high beams but not as noticeable. Live and drive in the ne georgia mountains, hazard in daytime and more at night. Adjusted headlights. Nothing they can do. It is a problem that has been reported to them by other kia Sportage owners and it is a design flaw so was told by service manager at lifetime kis. I wanted to know why when I purchased the auto was not informed of this major problem.

Considered a major safety hazard. No satisfactory answer was given. I felt like all they wanted to do was sell a car and I was willing to purchase another but would lose 10k in just a few months. Am still considering trading this car in so will have peace of mind on the road at night. See all problems of the Kia Motor Sportage. Driver side headlight lamp lens is turning yellow, very distorted.

Headlights and navigation system flicker and go out while driving at night. Lights went out while driving down the interstate. Came back on after about 20 seconds and continued to flicker. Afls appeared on the display, the owners manual said to turn off the car and restart it, this turned off the afls light but the lights and navigation system continue to flicker occasionally.

Scared to drive at night. Left headlight plug is defective. The contact owns a kia Sportage. The contact stated that the low beam and high beam headlights shorted out without warning.

The contact experienced the short in the lights during inclement weather a downpour and was uncertain if wires had been affected as well or any other components. The vehicle was not diagnosed by a dealer. The manufacturer was notified of the failure.

The VIN and failure mileage were not available. When purchased in may,the headlights had to be adjusted as they were aimed too high. The adjustment made the lights too low and with a very short "cut-off" point. It is almost impossible to see the roadway in front of the vehicle at night. The contact stated that the headlights were extremely dim.Lake Chevy helped make these videos. We are still working to obtain content for your car, however the video above is believed to have similar characteristics as your car.

2015 kia sportage headlight fuse location full

The video above shows how to check for blown fuses in the interior fuse box of your Kia Sportage and where the fuse panel diagram is located.

If your map light, stereo, heated seats, headlights, power windows or other electronic components suddenly stop working, chances are you have a fuse that has blown out. If your Sportage is experiencing electrical problems, you should always check the fuses first, because they are relatively easy to check and cheap to change.

Some Kias have multiple interior fuse boxes even the trunk - the video above will show you where the interior fuse box of your Sportage is located.

KIA Sportage (JE/KM; 2004-2010) fuses and relays

The more electronics your Sportage has, the more fuses it has. Some components may have multiple fuses, so make sure you check all of the fuses that are linked to the component in question. If you need to replace a blown fuse in your Sportage, make sure you replace it with one that has the same amperage as the blown fuse. If checking and replacing the fuse for the component in question doesn't work, we recommend seeking assistance from a trusted professional mechanic.

They should be able to figure out if the component needs to be replaced or if there is a short or some other problem with your Sportage. Burnt out brake lights increase your chance of getting rear ended - check and change yours today. Don't send mixed signals - if your turn signal doesn't blink, or blinks rapidly, you likely have a burnt out bulb. Many cars will burn or leak a little bit of oil.

Over time, this adds up and you might need to add some - learn how to here! Properly inflated tires is the easiest way to improve fuel economy. The right tire pressure is NOT on the side of your tire btw. On many cars, the high beam bulb runs at reduced power during the day - check 'em and change 'em! Getting Started Prepare for the repair. Remove Cover Locate interior fuse box and remove cover. Locate Bad Fuse Find the fuse that is tied to the bad component. Remove Fuse Take out the fuse in question and assess if blown.

Test Component Secure the cover and test component. More Info. Additional information on interior fuses. Video Description. Other videos you might find helpful.

Replace brake lights Burnt out brake lights increase your chance of getting rear ended - check and change yours today Kia Sportage EX 2. Change a rear blinker Don't send mixed signals - if your turn signal doesn't blink, or blinks rapidly, you likely have a burnt out bulb Kia Sportage EX 2.

Top up the oil level Many cars will burn or leak a little bit of oil.The system automatically turns off the headlights and parking lights when the driver removes the ignition key and opens the driver- side door. If necessary, to keep the lights on when the ignition key is removed, perform the following : 1 Open the driver-side door.

Lighting control The light switch has a Headlight and a Parklight position. To operate the lights, turn the knob at the end of the control lever to one of the following positions: 1 OFF position 2 Parklight position 3 Headlight position. Parklight position When the light switch is in the parklight position 1st positionthe tail, position, license and instrument panel lights are ON.

Headlight position When the light switch is in the headlight position 2nd position the head, tail, position, license and instrument panel lights are ON.

High - beam operation To turn on the high beam headlights, push the lever forward. The high-beam indicator will light when the headlight high beams are switched on. To prevent the battery from being discharged, do not leave the lights on for a prolonged time while the engine is not running. Flashing headlights To flash the headlights, pull the lever towards you. It will return to the normal low-beam position when released. The headlight switch does not need to be on to use this flashing feature.

Turn signals The ignition switch must be on for the turn signals to function. To turn on the turn signals, move the lever up or down. Green arrow indicators on the instrument panel indicate which turn signal is operating. They will selfcancel after a turn is completed. If the indicator continues to flash after a turn, manually return the lever to the OFF position. Lane change signals To signal a lane change, move the turn signal lever slightly and hold it in position.

The lever will return to the OFF position when released. If an indicator stays on and does not flash or if it flashes abnormally, one of the turn signal bulbs may be burned out and will require replacement.

NOTICE If an indicator flash is abnormally quick or slow, bulb may be burned out or have a poor electrical connection in the circuit. Front fog light if equipped Fog lights are used to provide improved visibility and avoid accidents when visibility is poor due to fog, rain or snow etc. To turn off the fog lights, turn the switch to OFF. Only use the fog lights when visibility is poor.

Unnecessary battery and generator drain could occur if the fog lights are used excessively. Daytime running light if equipped Daytime Running Lights DRL can make it easier for others to see the front of your vehicle during the day.

DRL can be helpful in many different driving conditions, and it is especially helpful after dawn and before sunset. The head light switch is ON. The parking brake engaged. Engine stops.

2015 kia sportage headlight fuse location full

XMTM satellite radio reception tips for antenna on the windshield for U. The XMTM satellite radio receiver that is fitted to your vehicle receives the necessary To operate the lights, turn the knob at the end of the control lever to one of the following positions: 1 OFF position 2 Parklight position 3 Headlight position Parklight position When the light switch is in the parklight position 1st positionthe tail, position, license and instrument panel lights are ON.


thoughts on “2015 kia sportage headlight fuse location full

Leave a Reply

Your email address will not be published. Required fields are marked *